![add information to bead tool 4 pattern add information to bead tool 4 pattern](https://img.informer.com/screenshots/5507/5507945_1_4.png)
(d) Slip through the tail of a "Step 7" pin, slip on a 4mm faceted, slip through the tail of a "Step 11" pin, slip through the head of one of the pins of the previous row. (c) Slip on a 4mm faceted, slip through the tail of a "Step 11" pin, slip on a 4mm faceted, slip through the head of a pin of the previous row. (b) Slip through the tail of a "Step 11" pin, slip on a 4mm faceted, slip through the tail of a "Step 10" pin, Slip through the head of one of the pins of the previous row. (a) Slip on a 4mm faceted, slip through the tail end of a "Step 7" pin, slip on a 4mm faceted, slip through the head of one of the pins of the previous row. Cut a 21" piece of wire and make a loop at one end. These will be referred to as "Step 11" pins.ġ2. Open up a pin and slip on a 6mm faceted and four 8mrn faceted. Open up a pin and slip on an 8mm faceted, two 10 mm crystal faceted and one 10mm faceted. Make eighteen (18) more pins in the same way as in step 7 ("Step 7" pins).ġ0. Then, slip on a 4mm faceted, slip through the tail of a "Step 6" pin, slip on an 8mm faceted, slip through the tail of a "Step 7" pin, slip on a 4mm faceted, slip through the head of one of the pins of the previous row. Slip on one 4mm faceted, slip the wire through the tail end of a "Step 6" pin, slip on one 8mm faceted, slip through the tail end of a "Step 7" pin, slip on a 4mm faceted, slip through the head of one of the pins of the previous row. Cut a 17" piece of wire and make a loop in one end.
![add information to bead tool 4 pattern add information to bead tool 4 pattern](https://images-na.ssl-images-amazon.com/images/I/61tGIwsUoXL._AC_SX425_.jpg)
Open up a pin and slip on one 8mm faceted, three 10mm faceted, close as before. These will be referred to as "Step 6" pins.ħ.
![add information to bead tool 4 pattern add information to bead tool 4 pattern](http://www.beadfx.com/wordpress/wp-content/uploads/2019/03/Capture0000.jpg)
Open up a pin and slip on one 10mm faceted bead and eight 12mm starflakes.
![add information to bead tool 4 pattern add information to bead tool 4 pattern](https://img.informer.com/screenshots/2771/2771966_2.jpg)
Twist wires together and trim as before.Ħ. Continue alternating around the row until you have used all the pins made in step 3 and 4 and have slipped through all nine pins of the previous row. Slip on a 4mm faceted, then through the tail of a 10mm pin, then slip on an 8mm faceted, then through the tail of a "Step 4" pin, then slip on a 4mm faceted, then through the head of one of the pins of the previous row. Slip on a 4mm faceted, then slip through the tail of one 10mm pin, then slip on an 8mm faceted, the slip through the tail of a "Step 4" pin, then slip on a 4mm facted, then through the head of one of the pins of the previous row. These will be referred to as "Step 4" pins.ĥ. Open up a pin and slip on two 12mm starflakes, three 18mm starflakes, two 12mm starflakes and one 10mm faceted bead. Make nine more 10mm pins in the same way as in step 1.Ĥ. Trim the wire to a 1/4" and bend the end in toward the center.ģ. Twist the ends of the wire together very tightly (the tighter the wire is pulled the sturdier the tree will be). Continue alternating beads and pins (making sure all the pins are facing the same direction) until there are nine pins and nine 4mm beads. Slip on a 4mrn faceted bead, then slip the wire through the tail end of one 10mm pin, slip on a 4mm, slip through the tail of a 10mm pin, slip on a 4mm and slip through the tail of a 10mm pin. Use the pliers to make a loop at one end to hold the pins on. Close the pin and use the pliers to squeeze the head of the pin so that it will not slip open. Open up a safety pin and slip on one 10mm faceted bead, two 12mm starflakes, three 18mm starflakes and two 12mm starflakes.